Product Description
Fast Connector Type A SC/UPC
Fast Connector Type A SC/APC
FTTH- Conector mecánico rápido SC/APC
Producto añadido!
Navegar por Lista de Deseos
El producto ya está en la lista de deseos!
Navegar por Lista de Deseos
Related Products
ADSS Single PP
Loose tube construction, tubes water blocking yarn filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, water blocking tape wrapped around the cable core, PE inner sheath, then aramid yarns and PE outer sheath.FTTH- Fast Connector Type B SC/APC
1.SC APC UPC single mode fast connector terminates the end of an optical fiber and enables quicker connection and disconnection than splicing. 2.The connectors mechanically couple and align the cores of fibers so light can pass. Better connectors lose very little light due to reflection or misalignment of the fibers.Outdoor EDFA EA1500
This equipment is an outdoor erbium-doped fiber amplifier independently researched and developed by the company. The product adopts high heat-conducting die-casting aluminum profiles as a whole. The housing has high thermal conductivity and good waterproof performance. It is a harsh environment and is not conducive to the secondary construction of remote areas. Network, the ideal product for long-distance transmission in 1550nm optical signalsEDFA 8 outs
➢ Adopts Er Yb Codoped double-clad fiber technology ➢ Output ports: 8-16-32 optional ➢ Optical output power: total output up to 3W ➢ Low noise figure: <5dB when input is 0dBm ➢ Perfect network management interface support web English Brower, in line with standard SNMP network management; ➢ Intelligent temperature control system make the power consumption lower All our prices is in USDOPTICAL FIBER ASU
G.652D Aerial Self-Supported ASU Fiber Optic Cable has a loose tube structure and water-resistant gel compound to provide crucial protection for the fiber. Over the tube, water-blocking material is applied to keep the cable watertight. Two parallel fiber reinforced plastic (FRP) elements are placed on the two sides. The cable is covered with a single PE outer sheath. It is especially suitable for installation in aerial for long-distance communicationGYXTW
• Outer Jacket MDPE • Corrugated steel tape covered of Phospated Steel • Loose tube steel ribbon attached with color melt glue • Range of application: for long distance and loca communication • Installation method: in pipeline or underground duct or aerial assembly • Application temperature: -40 ~ +70ADSS Doube PBT
Loose tube construction, tubes jelly filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, water blocking tape wrapped around the cable core, PE inner sheath, then aramid yarns and PE outer sheath.FTTH- Fast Connector Type Y SC/UPC
Fiber optic fast connector designed for FTTH. It is a new generation of fiber connector used in assembly. It can provide open flow and precast type, which optical and mechanical specification meets the standard optical fiber connector. It is designed for high quality and high eddiciency for installation, the structure of crimping position is a unique design.
VISUAL FAULT LOCATOR
Pen design, easy to carry and use, easy to check fiber faults with visual light, Portable and rugged, has always, flash, slow flash 3 modes of operation, Master switch in the pen tail pipe
• Easy and Accurate Identification - It can easily and accurately detect and locate fiber breaks, poor connections, bending or cracking. The detector will emit a 650nm bright light for fiber tracing, breaks or faults in the fiber will refract the light, creating a bright glow around the faulty area.
Read more EDFA 19dB x 32 Outs
- Output ports: 16 or 32 (optional) Optical output power: total output up to 23W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower
OPTICAL FIBER OPGW
This specification covers COMCAST® OPGW for the installation on high voltage overhead power lines. The cable contains optical fibers for data transmission and telecom purposes and is installed instead of a ground wire. The specification describes the basic design of COMCAST® OPGW with its main components: the fibers, the optical fiber unit and the cable armoring. Furthermore this specification contains information concerning the quality assurance during manufacturing, the final acceptance tests, the type tests and the packaging.Fiber ADSS Span 100
Loose tube construction, tubes jelly filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, water blocking tape wrapped of the cable core, aramid yarn reinforced and PE outer sheath. the prices is for 1 KM, and the purchase is for 5 KM reelEDFA 19dB x 16 Outs
- Output ports: 16 or 32 (optional)
- Optical output power: total output up to 10W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower
Fiber GYFTC8Y
Loose tube construction, tubes jelly filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, compound filled in the apertures of the cable core, PE outer sheath with messenger wires combined. The prices is for 1 KM, and the purhase is for 6 KM reels.Stripper Cable 500
The FZ136 coaxial cable stripper removes the aluminum jacket and dielectric in a single, fast and precise operation. It is manual or drill-assisted operation. This 500 line coaxial cable stripping tool has a T-shaped handle with a built-in 3/8-inch (9.5mm) drill adapter. The long-lasting cutting blade is heat-treated to make smooth chamfers. Plus you can replace just the blade without spending the entire dielectric removal bit. Spiral-fluted, heat-treated steel bit coring. Strong, durable, all-metal construction.FUSION SPLICE XFO-628
Handheld Fusion Splicer, cost effective and smart appearance, reliable quality, XFO-628 is a special design for the installation, operation and maintenance of optical fiber specially design a precision, durable, convenient optical fiber construction instrument. Widely used in the construction, inspection, maintenance of fiber cable.WOS4000
The WOS4000 optical communication platform is the brand-new 3rd generation product based on professional experience in development, manufacturing, and sales of CATV transmission equipment over 20 years. It provides powerful function and flexible configuration in HFC optical data transmission solutions. The standard 4RU metal rack contains sixteen compact slots and each can be installed any functional module able to perform hot plug. Built-in dual-power hot backup, efficient fan cooling and appropriate redundant backup of functional modules contribute to carrier-class reliability.Amplifier Bi-directional 35-90V
Outdoor trunk bidirectional amplifier is mainly used for bidirectional trunk transmission of CATV television image signal, digital TV signa, and telephone voice signals and data (or compressed data) signal. Advanced and mature circuits, scientific and reasonable process structures and high quality materials, ensure the excellent performance. It is the first choice equipment to build large or middle- sized CATV bidirectional transmission network. +FTTH- Fast Connector Type Y SC/APC
Fiber optic fast connector designed for FTTH. It is a new generation of fiber connector used in assembly. It can provide open flow and precast type, which optical and mechanical specification meets the standard optical fiber connector. It is designed for high quality and high eddiciency for installation, the structure of crimping position is a unique design.
Fiber optic tool cases prepared for the diverse types of finishing, inspection and cleaning that are needed in fiber optic and
FTTH installations:
• Inspection and cleaning of all fiber optic assemblies made.
• installation and testing FTTH Fiber Optic networks.
• preparation of fiber optic mergers in an FTTH network.
• tools and materials needed to terminate connectors cleanly and easily.
Read more FTTH- Fast Connecor SC/UPC
Optical fast connector takes use of the latest generation of Rapid Ready-Terminal technology. After terminating, both the optical and mechanical performances reach the standard for patchcord and meet the demand for making patchcord on site by mechanical splicing.CS-6 Cleaver
Bare fiber diameter: 0.25mm~ 0.9mm Outercoat diameter: 125 (micro)m Fiber type: Single tube fiber and ribbon fiber (Exchangeable) Cleaved Length: 9~16mm (Φ0.25) 10~16(Φ0.9) Cleaved Angle: 0.5 °C Blade life: 36000 cleaves Mode: Semiautomatic Dimension: 59mm (W)* 55mm(D)* 49mm(H) Weight: 255g ]EDFA 23dB x 32 Outs
- Output ports: 16 or 32 (optional) Optical output power: total output up to 23W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower