Product Description
ADSS Double PP
ADSS 250 span
ADSS Double PBT
ADSS Doube PBT
Loose tube construction, tubes jelly filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, water blocking tape wrapped around the cable core, PE inner sheath, then aramid yarns and PE outer sheath.
Producto añadido!
Navegar por Lista de Deseos
El producto ya está en la lista de deseos!
Navegar por Lista de Deseos
Related Products
EDFA 8 outs
➢ Adopts Er Yb Codoped double-clad fiber technology ➢ Output ports: 8-16-32 optional ➢ Optical output power: total output up to 3W ➢ Low noise figure: <5dB when input is 0dBm ➢ Perfect network management interface support web English Brower, in line with standard SNMP network management; ➢ Intelligent temperature control system make the power consumption lower All our prices is in USDZTE ONT F660
GPON Optical Network Terminal designed fot FTTH scenario. It support L3 function to help suscribers construct intelligent home network. It provides subscriber ricj, color full,individualized, convenient and confortable service including voice, video ( IPTV) and high speed intenet accessFTTH- Fast Connector Type B SC/UPC
1.SC APC UPC single mode fast connector terminates the end of an optical fiber and enables quicker connection and disconnection than splicing. 2.The connectors mechanically couple and align the cores of fibers so light can pass. Better connectors lose very little light due to reflection or misalignment of the fibers.AIR BLOWING DUCT FIBER
Optical Fibers are housed in loose tubes that are made of high-modulus plastic and filled with tube filling compound. The tubes (and fillers) are stranded around a non-metallic central strength member andsurrounded with dry water-blocking material to form a cable core. An extremely thin outer PE sheath is extruded outside the core.
Fiber optic tool cases prepared for the diverse types of finishing, inspection and cleaning that are needed in fiber optic and
FTTH installations:
• Inspection and cleaning of all fiber optic assemblies made.
• installation and testing FTTH Fiber Optic networks.
• preparation of fiber optic mergers in an FTTH network.
• tools and materials needed to terminate connectors cleanly and easily.
Read more FTTH- Fast Connector Type Y SC/UPC
Fiber optic fast connector designed for FTTH. It is a new generation of fiber connector used in assembly. It can provide open flow and precast type, which optical and mechanical specification meets the standard optical fiber connector. It is designed for high quality and high eddiciency for installation, the structure of crimping position is a unique design.FTTH- Fast Connecor SC/UPC
Optical fast connector takes use of the latest generation of Rapid Ready-Terminal technology. After terminating, both the optical and mechanical performances reach the standard for patchcord and meet the demand for making patchcord on site by mechanical splicing.OTDR AE1001
The last thing a fiber maintenance technician needs is a double armful of bulky, feature-bloated equipment to bog down the job. The new AE1001 from Deviser Instruments is a sleek, zerofuss OTDR weighing less than 1 kg that tests the common 1310 & 1550nm wavelengths in 5s flat. Low power consumption and a solid 2500mAH battery allow the AE1001 to run automated, manual, or real-time tests continuously for over 4 hours, and are supplemented with the always-handy OPM and VFLFiber GYFTC8Y
Loose tube construction, tubes jelly filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, compound filled in the apertures of the cable core, PE outer sheath with messenger wires combined. The prices is for 1 KM, and the purhase is for 6 KM reels.EDFA 19dB x 32 Outs
- Output ports: 16 or 32 (optional) Optical output power: total output up to 23W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower
OPTICAL FIBER ASU
G.652D Aerial Self-Supported ASU Fiber Optic Cable has a loose tube structure and water-resistant gel compound to provide crucial protection for the fiber. Over the tube, water-blocking material is applied to keep the cable watertight. Two parallel fiber reinforced plastic (FRP) elements are placed on the two sides. The cable is covered with a single PE outer sheath. It is especially suitable for installation in aerial for long-distance communication
VISUAL FAULT LOCATOR
Pen design, easy to carry and use, easy to check fiber faults with visual light, Portable and rugged, has always, flash, slow flash 3 modes of operation, Master switch in the pen tail pipe
• Easy and Accurate Identification - It can easily and accurately detect and locate fiber breaks, poor connections, bending or cracking. The detector will emit a 650nm bright light for fiber tracing, breaks or faults in the fiber will refract the light, creating a bright glow around the faulty area.
Read more OPTICAL FIBER OPGW
This specification covers COMCAST® OPGW for the installation on high voltage overhead power lines. The cable contains optical fibers for data transmission and telecom purposes and is installed instead of a ground wire. The specification describes the basic design of COMCAST® OPGW with its main components: the fibers, the optical fiber unit and the cable armoring. Furthermore this specification contains information concerning the quality assurance during manufacturing, the final acceptance tests, the type tests and the packaging.FUSION SPLICE XFO600
The machine employs high-speed image processing technology and special positioning technology, allowing the total process of fusion splicing to be finished within 10 seconds. Large-screen LCD clearly demonstrates every stage of optical-fiber fusion splicing. As the machine is compact in size, light in weight, it is ideal to work in outdoor environment. In addition, it is easy to operate, fuses fast, with low fusion loss, especially suitable for the construction and maintenance of the optical-fiber works built in a wide range of sectors including telecommunications, broadcast & TV, railway, petrochem, electricity, army, police, as well as teaching and research of scientific institutes. In order to finish the fusion operations more accurately, please thoroughly read this Manual. All our prices is in USDAmplifier Bi-directional 35-90V
Outdoor trunk bidirectional amplifier is mainly used for bidirectional trunk transmission of CATV television image signal, digital TV signa, and telephone voice signals and data (or compressed data) signal. Advanced and mature circuits, scientific and reasonable process structures and high quality materials, ensure the excellent performance. It is the first choice equipment to build large or middle- sized CATV bidirectional transmission network. +FTTH- Fast Connector Type Y SC/APC
Fiber optic fast connector designed for FTTH. It is a new generation of fiber connector used in assembly. It can provide open flow and precast type, which optical and mechanical specification meets the standard optical fiber connector. It is designed for high quality and high eddiciency for installation, the structure of crimping position is a unique design.EDFA 23dB x 32 Outs
- Output ports: 16 or 32 (optional) Optical output power: total output up to 23W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower