Product Description
ADSS PBT 100 span
Fiber ADSS Span 100
Loose tube construction, tubes jelly filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, water blocking tape wrapped of the cable core, aramid yarn reinforced and PE outer sheath.
Related Products
Fiber GYFTC8Y
Loose tube construction, tubes jelly filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, compound filled in the apertures of the cable core, PE outer sheath with messenger wires combined. The prices is for 1 KM, and the purhase is for 6 KM reels.
EDFA 19dB x 32 Outs
- Output ports: 16 or 32 (optional) Optical output power: total output up to 23W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower
FTTH- Fast Connector Type Y SC/APC
Fiber optic fast connector designed for FTTH. It is a new generation of fiber connector used in assembly. It can provide open flow and precast type, which optical and mechanical specification meets the standard optical fiber connector. It is designed for high quality and high eddiciency for installation, the structure of crimping position is a unique design.
EDFA 8 outs
➢ Adopts Er Yb Codoped double-clad fiber technology ➢ Output ports: 8-16-32 optional ➢ Optical output power: total output up to 3W ➢ Low noise figure: <5dB when input is 0dBm ➢ Perfect network management interface support web English Brower, in line with standard SNMP network management; ➢ Intelligent temperature control system make the power consumption lower All our prices is in USD
EDFA 19dB x 8 Outs
- Output ports: 8, 16 32 (optional)
- Optical output power: total output up to 10W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower
Stripper Cable 500
The FZ136 coaxial cable stripper removes the aluminum jacket and dielectric in a single, fast and precise operation. It is manual or drill-assisted operation. This 500 line coaxial cable stripping tool has a T-shaped handle with a built-in 3/8-inch (9.5mm) drill adapter. The long-lasting cutting blade is heat-treated to make smooth chamfers. Plus you can replace just the blade without spending the entire dielectric removal bit. Spiral-fluted, heat-treated steel bit coring. Strong, durable, all-metal construction.
Fiber optic tool cases prepared for the diverse types of finishing, inspection and cleaning that are needed in fiber optic and
FTTH installations:
• Inspection and cleaning of all fiber optic assemblies made.
• installation and testing FTTH Fiber Optic networks.
• preparation of fiber optic mergers in an FTTH network.
• tools and materials needed to terminate connectors cleanly and easily.
Read more 
WOS4000
The WOS4000 optical communication platform is the brand-new 3rd generation product based on professional experience in development, manufacturing, and sales of CATV transmission equipment over 20 years. It provides powerful function and flexible configuration in HFC optical data transmission solutions. The standard 4RU metal rack contains sixteen compact slots and each can be installed any functional module able to perform hot plug. Built-in dual-power hot backup, efficient fan cooling and appropriate redundant backup of functional modules contribute to carrier-class reliability.
ZTE ONT F660
GPON Optical Network Terminal designed fot FTTH scenario. It support L3 function to help suscribers construct intelligent home network. It provides subscriber ricj, color full,individualized, convenient and confortable service including voice, video ( IPTV) and high speed intenet access
AE3100C
Featuring intuitive touchscreen controls, real-time data analysis, and more, the AE3100 is the ideal test instrument for constructing, deploying, maintaining, and authenticating FTTx networks - as well as verifying access networks. Multiple models and configuration options ensure your unique measurement needs are covered. Dual or multiple wavelengths and a choice of dynamic ranges (spanningfrom 28 to 39dB) are also available
Fiber FTTH KIT 68
Fiber optic tool cases prepared for the diverse types of finishing, inspection and cleaning that are needed in fiber optic and FTTH installations: • Inspection and cleaning of all fiber optic assemblies made. • installation and testing FTTH Fiber Optic networks. • preparation of fiber optic mergers in an FTTH network. • tools and materials needed to terminate connectors cleanly and easily.
FTTH- Fast Connector Type B SC/APC
1.SC APC UPC single mode fast connector terminates the end of an optical fiber and enables quicker connection and disconnection than splicing. 2.The connectors mechanically couple and align the cores of fibers so light can pass. Better connectors lose very little light due to reflection or misalignment of the fibers.
EDFA 19dB x 16 Outs
- Output ports: 16 or 32 (optional)
- Optical output power: total output up to 10W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower
VISUAL FAULT LOCATOR
Pen design, easy to carry and use, easy to check fiber faults with visual light, Portable and rugged, has always, flash, slow flash 3 modes of operation, Master switch in the pen tail pipe
• Easy and Accurate Identification - It can easily and accurately detect and locate fiber breaks, poor connections, bending or cracking. The detector will emit a 650nm bright light for fiber tracing, breaks or faults in the fiber will refract the light, creating a bright glow around the faulty area.
Read more 
ADSS Single PP
Loose tube construction, tubes water blocking yarn filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, water blocking tape wrapped around the cable core, PE inner sheath, then aramid yarns and PE outer sheath.
FTTH- Fast Connecor SC/UPC
Optical fast connector takes use of the latest generation of Rapid Ready-Terminal technology. After terminating, both the optical and mechanical performances reach the standard for patchcord and meet the demand for making patchcord on site by mechanical splicing.
FTTH- Fast Connector Type B SC/UPC
1.SC APC UPC single mode fast connector terminates the end of an optical fiber and enables quicker connection and disconnection than splicing. 2.The connectors mechanically couple and align the cores of fibers so light can pass. Better connectors lose very little light due to reflection or misalignment of the fibers.
Amplifier Bi-directional 35-90V
Outdoor trunk bidirectional amplifier is mainly used for bidirectional trunk transmission of CATV television image signal, digital TV signa, and telephone voice signals and data (or compressed data) signal. Advanced and mature circuits, scientific and reasonable process structures and high quality materials, ensure the excellent performance. It is the first choice equipment to build large or middle- sized CATV bidirectional transmission network. +
FUSION SPLICE XFO600
The machine employs high-speed image processing technology and special positioning technology, allowing the total process of fusion splicing to be finished within 10 seconds. Large-screen LCD clearly demonstrates every stage of optical-fiber fusion splicing. As the machine is compact in size, light in weight, it is ideal to work in outdoor environment. In addition, it is easy to operate, fuses fast, with low fusion loss, especially suitable for the construction and maintenance of the optical-fiber works built in a wide range of sectors including telecommunications, broadcast & TV, railway, petrochem, electricity, army, police, as well as teaching and research of scientific institutes. In order to finish the fusion operations more accurately, please thoroughly read this Manual. All our prices is in USD
OPTICAL FIBER OPGW
This specification covers COMCAST® OPGW for the installation on high voltage overhead power lines. The cable contains optical fibers for data transmission and telecom purposes and is installed instead of a ground wire. The specification describes the basic design of COMCAST® OPGW with its main components: the fibers, the optical fiber unit and the cable armoring. Furthermore this specification contains information concerning the quality assurance during manufacturing, the final acceptance tests, the type tests and the packaging.
FTTH- Fast Connector Type Y SC/UPC
Fiber optic fast connector designed for FTTH. It is a new generation of fiber connector used in assembly. It can provide open flow and precast type, which optical and mechanical specification meets the standard optical fiber connector. It is designed for high quality and high eddiciency for installation, the structure of crimping position is a unique design.
OTDR AE1001
The last thing a fiber maintenance technician needs is a double armful of bulky, feature-bloated equipment to bog down the job. The new AE1001 from Deviser Instruments is a sleek, zerofuss OTDR weighing less than 1 kg that tests the common 1310 & 1550nm wavelengths in 5s flat. Low power consumption and a solid 2500mAH battery allow the AE1001 to run automated, manual, or real-time tests continuously for over 4 hours, and are supplemented with the always-handy OPM and VFL
CS-6 Cleaver
Bare fiber diameter: 0.25mm~ 0.9mm Outercoat diameter: 125 (micro)m Fiber type: Single tube fiber and ribbon fiber (Exchangeable) Cleaved Length: 9~16mm (Φ0.25) 10~16(Φ0.9) Cleaved Angle: 0.5 °C Blade life: 36000 cleaves Mode: Semiautomatic Dimension: 59mm (W)* 55mm(D)* 49mm(H) Weight: 255g ]
ADSS Span 250
Loose tube construction, tubes jelly filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, compound filled in the apertures of the cable core, then PE inner sheath, aramid yarn reinforced and PE outer sheath.
Outdoor EDFA EA1500
This equipment is an outdoor erbium-doped fiber amplifier independently researched and developed by the company. The product adopts high heat-conducting die-casting aluminum profiles as a whole. The housing has high thermal conductivity and good waterproof performance. It is a harsh environment and is not conducive to the secondary construction of remote areas. Network, the ideal product for long-distance transmission in 1550nm optical signals
AIR BLOWING DUCT FIBER
Optical Fibers are housed in loose tubes that are made of high-modulus plastic and filled with tube filling compound. The tubes (and fillers) are stranded around a non-metallic central strength member andsurrounded with dry water-blocking material to form a cable core. An extremely thin outer PE sheath is extruded outside the core.
EDFA 23dB x 32 Outs
- Output ports: 16 or 32 (optional) Optical output power: total output up to 23W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower