Product Description
Visual Fault Locator
VISUAL FAULT LOCATOR
Pen design, easy to carry and use, easy to check fiber faults with visual light, Portable and rugged, has always, flash, slow flash 3 modes of operation, Master switch in the pen tail pipe
• Easy and Accurate Identification – It can easily and accurately detect and locate fiber breaks, poor connections, bending or cracking. The detector will emit a 650nm bright light for fiber tracing, breaks or faults in the fiber will refract the light, creating a bright glow around the faulty area.
Producto añadido!
Navegar por Lista de Deseos
El producto ya está en la lista de deseos!
Navegar por Lista de Deseos
Related Products
OTDR 4000
Handheld Optical Time Domain Reflectometry is a new generation of intelligent optical-fibre communication instrument. It is able to display the loss distribution curves of optical fibers and optical cables, measure the attenuation factors of optical fibers and optical cables, loss between points and at joints. It is also able to measure the length of optical fibers and optical cables, the distance between two points, identify the connecting, fault, and disconnecting locations of optical fibers and optical cables. It is widely used in the construction, maintenance, measurement, emergency repair of optical-fibre communication system works; also used in the development, manufacturing and measurement of optical fibers and optical cables:Analyzer S7200
TV Signal Analyzer provides fast, easy real-time analysis and monitoring of terrestrial, cable, and satellite TVsignals (8VSB, QAM [J.83A/C/C2], QPSK, 8PSK, and PAL,SECAM, & NTSC RF Channels). The range of capabilities offered by the S7200 includes all measurements requiredto install, maintain, and troubleshoot 8VSB transmitters and includes complete RF analysis and logging, along with transport stream recording.ADSS Single PP
Loose tube construction, tubes water blocking yarn filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, water blocking tape wrapped around the cable core, PE inner sheath, then aramid yarns and PE outer sheath.XFO-520B Optical Power Meter
XFO520 a PON Power Meter (pon test instrument) is specially designed for PON network construction and maintenance which can be connected between OLT and ONT. The voice, data, video signal (1310/1490/1550) online can be measured synchronously and optical power value (1310/1490/1550) can be displayed with this meter. It’s a useful site test tool for the engineers of PON network and maintenance operators. Notice: There are two connector’s type of PON Power Meter: SC/PC and SC/APC, default connector is SC/APC Customers must specify the connector type before ordering this modeEDFA 19dB x 8 Outs
- Output ports: 8, 16 32 (optional)
- Optical output power: total output up to 10W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower
EDFA 8 outs
➢ Adopts Er Yb Codoped double-clad fiber technology ➢ Output ports: 8-16-32 optional ➢ Optical output power: total output up to 3W ➢ Low noise figure: <5dB when input is 0dBm ➢ Perfect network management interface support web English Brower, in line with standard SNMP network management; ➢ Intelligent temperature control system make the power consumption lower All our prices is in USDAE2200E- APC
As the demand for bandwidth continues to soar, with higherthan-ever smartphone and streaming video usage, cable operators must face the challenge deploying fiber deeper into the network. And because efficiency, speed, accuracy, and reliability metrics are key for increasing workforce productivity, the natural conclusion is simple: communications service providers (CSP) require a high-performance, efficient, yet affordable test equipment for installing future networks such as FTTx, RFoG and RF PON.XFO-306
Fiber Identifier is a tool necessary for be maintenance of optical fibers used to identify be optical fibers not yet damage. It can detect anywhere in single-mode fiber and multiple mode fiber- During the maintenance, installation, wiring fiber without interruption our business. By transmitting the signal with modulation sound (270Hz, 1KHz, 2KHz) into one end of fiber 1310nm or 1550nm, the identifier can identify the fiber from the route, Fiber identifier can indicate thebusiness direction.FUSION SPLICE XFO600
The machine employs high-speed image processing technology and special positioning technology, allowing the total process of fusion splicing to be finished within 10 seconds. Large-screen LCD clearly demonstrates every stage of optical-fiber fusion splicing. As the machine is compact in size, light in weight, it is ideal to work in outdoor environment. In addition, it is easy to operate, fuses fast, with low fusion loss, especially suitable for the construction and maintenance of the optical-fiber works built in a wide range of sectors including telecommunications, broadcast & TV, railway, petrochem, electricity, army, police, as well as teaching and research of scientific institutes. In order to finish the fusion operations more accurately, please thoroughly read this Manual. All our prices is in USDMultimeter DUT120C
DUT120C is 4000 count notebook, type auto-ranging digital multimeter with fallowing advantage: complete function, stable, performance, high accuracy, low power consumption, novel structure. High. Degree of current. Frequency. Duty cycle, resistance, capacitance, diode forward voltage drops and continuity, and become and ideal choice for measurement.FIBER IDENTIFIER TM-OFI 401L
---Macro bending measurement. Macro bends are the use of fiber-optic bending leak out when the weak optical signal, optical signal to detect the direction and intensity. Does not damage optical fiber, without interrupting communications, and direct detection of 25mm bare fiber, 0.9mm and 2.5mm fiber casing tight jumper. ---Tone identification, Optical Fiber Identifier can detect optical signals in the tone signal a fixed load, 270Hz, 1KHz and 2KHz, to identify a specific optical fiber, can quickly find the necessary fiber. ---Build in VFL function.The output power of Optical Fiber Identifier is 10 mW.(Optional function) ---Low battery monitoring function, when battery power is insufficient , the Low battery LED will remind users to change batteries.WOS4000
The WOS4000 optical communication platform is the brand-new 3rd generation product based on professional experience in development, manufacturing, and sales of CATV transmission equipment over 20 years. It provides powerful function and flexible configuration in HFC optical data transmission solutions. The standard 4RU metal rack contains sixteen compact slots and each can be installed any functional module able to perform hot plug. Built-in dual-power hot backup, efficient fan cooling and appropriate redundant backup of functional modules contribute to carrier-class reliability.Outdoor EDFA EA1500
This equipment is an outdoor erbium-doped fiber amplifier independently researched and developed by the company. The product adopts high heat-conducting die-casting aluminum profiles as a whole. The housing has high thermal conductivity and good waterproof performance. It is a harsh environment and is not conducive to the secondary construction of remote areas. Network, the ideal product for long-distance transmission in 1550nm optical signalsAE8500
The AE8500 is a high precision, high-resolution optical spectrum analyzer with a wavelength range of 1250 ~ 1650nm. Users can test optical signals with excellent accuracy, and the 12.1" LCD touchscreen and concise UI design make the AE8500 easy to master. It also provides customizable CWDM/DWDM testing, in-band OSNR, light source, EDFA, fiber probe, auto testing, and more. The AE8500 meets the optical spectrum analysis requirements for several years to come - at superior cost-performance.OPN3327 Insertion/Return Loss Test Station
OPN3327 series Insertion/Return Loss Test Station is a precise instrument, which be adopted latest advantages from current instruments and improved to clients applications. It greatly improves the efficiency of IL test of optical devices which combines the two wavelengths testing result in one short test. It has extensive applications in the fiber cable, fiber passive device, fiber active device and optical communication system. It is suitable to perform the QC testing and sample character testing for fiber manufacturerGYXTW
• Outer Jacket MDPE • Corrugated steel tape covered of Phospated Steel • Loose tube steel ribbon attached with color melt glue • Range of application: for long distance and loca communication • Installation method: in pipeline or underground duct or aerial assembly • Application temperature: -40 ~ +70MINI OTDR T-OT560-A26D
- Nine-in-one function
- The 4.3-inch full-view capacitive touch screen supports multi-touch
- Cover plate type tempered glass panel, don't worry about screen scratch
- Support horizontal version, vertical version, perfect fusion of the two habits of user operations
- Support charging treasure charging, do not worry about the battery is not enough
- In line with the international standards of test data with perfect simulation software, so that your report more simple
- Sink type light port design, so that the instrument light port to get better protection
- Support U disk, SD card and Micro USB export data protection
- Any interface supports screen capture
Fiber optic tool cases prepared for the diverse types of finishing, inspection and cleaning that are needed in fiber optic and
FTTH installations:
• Inspection and cleaning of all fiber optic assemblies made.
• installation and testing FTTH Fiber Optic networks.
• preparation of fiber optic mergers in an FTTH network.
• tools and materials needed to terminate connectors cleanly and easily.
Read more FIBER IDENTIFIER TM501
Optical Fiber Identifier is an important tool for optical maintenance, which is used for nondestructive fiber identification project. Meanwhile it also has Visual Fault Locator module with fault location function and power meter function. Using the macro bending technology on line for nondestructive testing, It can measure the signal direction and power and avoid mis-operation resulting in interrupted lines. Macro bending measurement. Macro bends are the use of fiber-optic bending leak out when the weak optical signal, optical signal to detect the direction and intensity. Doesn’t damage optical fiber, without interrupting communications, and direct detection of 2.5mm bare fiber, 0.9mm and 2.5mm fiber casing tight jumperEDFA 19dB x 16 Outs
- Output ports: 16 or 32 (optional)
- Optical output power: total output up to 10W
- Low noise figure: <5dB when input is 0dBm
- Perfect network management interface, in line with standard SNMP network management
- Intelligent temperature control system make the power consumption lower
ADSS Doube PBT
Loose tube construction, tubes jelly filled, elements (tubes and filler rods) laid up around non-metallic central strength member, polyester yarns used to bind the cable core, water blocking tape wrapped around the cable core, PE inner sheath, then aramid yarns and PE outer sheath.
The DS2500Q is a rugged, handheld tool for installation, maintenance and troubleshooting HFC networks. This compact and simple-to-use instrument has an integrated DOCSIS 3.0 cable modem and supports all types of QAM and analog signal measurements such as HUM, modulation depth, MER, BER, constellation display, spectrum, power level and sweep.
Read more